How To Jump Start Your Car In The Rain

How To Jump Start Your Car In The Rain: The Ultimate Guide

Ever tried to jump start a car in the rain? It’s not easy to do, and it’s definitely not easy to do well. But you can do it if you follow the process below. This is a guide for those of you who are living in a rainy climate, and it was written by a person who has successfully jump started a car in the rain.

You can jumpstart a car in the rain using jumper cables and a car with a good battery. Turn both vehicles off and then attach the jumper cables to the batteries in the right sequence. Now, start the car with a good battery to charge the dead battery for a few minutes, and then start the car with the dead battery. Once it starts, drive it for 20-25 minutes to allow the alternator to charge the battery. That’s it.

This is how you can jumpstart a car in the rain. To learn everything step-by-step in detail, you’ll need to stick to this article till the end.

First of all, you should know what you’ll need to jumpstart your car in the rain.

What You’ll Need?

Following are the things that you’ll require to execute the process-

  • Jumper cables
  • A vehicle with a good battery
  • Anything for covering such as umbrella

These are the things that you’ll need to awake your dead battery in the rain. Now you must be thinking, isn’t it dangerous to jumpstart a car in the rain? Well, I knew that you’ll have this question and that I’ve answered next along with a couple of precautions that you’ve to take.

Is It Safe to Jumpstart a Car in the Rain?

It’s essential to clear your doubts first and then jump to the steps-

  • It’s all safe to jump start a car in the rain if you know how to do things in the right order. The amperage of a car battery is around 48-50 Ah, which is pretty safe to work with during rain.
  • Check for any cut or damage to your jumper cables. The jumper cables are supposed to be in good condition to not cause any short circuit in the battery.
  • Do not touch both terminals of your car battery simultaneously and if you have any gloves, put them on.
  • Use an umbrella or anything to cover the batteries from water droplets while connecting the jumper cables. It wouldn’t create any problem if the battery terminals get wet but prevent it from rain as much as possible.

So these are a couple of precautions and instructions that you need to keep in your mind, and I hope all your doubts are clear. Now you’re ready to follow the step-by-step process.

How to Jump Start a Car in the Rain?

Here’re the steps that you need to follow to jump start your car in the rain. Make sure you follow the steps in the same way they’re mentioned-

Step 1- First of all, make sure the ignition and all the electrical devices of the dead car are switched off, and the key is removed.

Step 2- Park the vehicle with the good battery as close to the dead car as possible so that the jumper cables can comfortably reach the terminals of both the battery. Make sure to keep a short distance between both the vehicles.

Step 3- Pop the hood of the dead car and use an umbrella or any water-resistant material as a cover to prevent the battery from rain. As I’ve already mentioned, it wouldn’t create any problem even if the battery gets wet, but it’s important to prevent it from rain as much as possible.

Step 4- Turn the vehicle with a good battery off and remove the key from the ignition. After that, pop the hood.

Step 5- Locate the batteries of both the vehicles and then attach the jumper cable’s red (+) clamp to the positive (+) terminal of the dead battery and the other end of the red (+) clamp to the positive (+) terminal of the good battery.

Step 6- Now, attach the jumper cable’s black (-) clamp to the negative (-) terminal of the good battery and the other end of the black (-) clamp to an earth point of the dead battery. Any metal surface away from the battery can be used as an earth point, and you can attach the other end of the black (-) clamp to it. Make sure the clamps of both the batteries are not touching each other.

Step 7- Start the car with the good battery and leave it for a few minutes.

Step 8- Now, attempt to start the car with the dead battery. Once it starts, keep it turned on, remove the negative (-) clamp of the dead battery first, and then remove the same battery’s positive (+) clamp. Make sure both the clamps aren’t touching each other.

Step 9- Now, Remove the negative (-) clamp of the good battery and then remove the positive (+) clamp.

Step 10- Now, get in the car with the dead battery and drive it for 20-25 minutes so that the alternator can charge the battery. Here you’re done.

Step 11- Your battery isn’t fully charged, so as soon as you can, recharge your battery with a good quality car battery charger so that it gets fully charged and work optimally.

This is how you can jump start a car in the rain. All these steps are practically done, and they work every time.

Conclusion

So this is how you can jumpstart a car in the rain. It’s pretty easy and safe to jumpstart a car in the rain if you follow the steps correctly. The car battery often gets drained, and that’s why it’s essential to take care of it. Make sure to check the condition of your car battery at least once in 6 months.

Frequently Asked Questions (FAQs)

Following are some frequently asked questions related to jump starting a car in the rain-

Is it safe to jumpstart a car in the rain?

Yes, it’s all safe because the voltage of a car battery isn’t high enough. All you need to do is connect the jumper cables in the right sequences and make sure while connecting it, you’re using an umbrella or anything as a cover to prevent the battery terminals from water droplets.

Yes, the voltage of a vehicle battery isn’t high enough to hurt you, even if it’s wet. You can go ahead and jump your car without any worry.

It’s not dangerous as long as the jumper cables are in good condition. If your jumper cables are damaged or in poor condition, then you should avoid using them and figure out any other way to start your vehicle.

There won’t be any problem if your jumper cables are in good condition. Make sure you dry them with a cloth after using so that they don’t get rusted or corroded and work well when you use them next time.

Leave a Comment

Your email address will not be published.